| Rated rpm | 2200 rpm |
|---|---|
| Operating Weight | 21,848 lb 9910 kg |
No blade mounted GNSS antenna(s), cables to worry about damaging with cab top GNSS antenna. Reduced risk of theft due to low visibility as viewed from ground level.
Robust stroke sensing hydraulic cylinders employ proven Komatsu sensor technologies for accurate finish grade performance. Stroke sensing angle cylinder allows machine control system to know the angle of the blade.
Chassis mounted IMU and intelligent logic enables accurate grading performance without blade mounted sensors.
| Model | Komatsu SAA4D95LE-7* | |
| Type | 4-cycle, water-cooled, direct injection | |
| Aspiration | Variable flow turbocharged, air-to-air aftercooled | |
| Number of cylinders | 4 | |
| Bore x stroke | 3.75" x 4.52" | 95 mm x 115 mm |
| Piston displacement | 199 in³ | 3.26 ltr |
| Governor | All-speed, electronic | |
| Horsepower: | ||
| SAE J1995 - Gross | 107 HP | 79 kW |
| ISO 9249 / SAE J1349 - Net | 105 HP | 78 kW |
| Rated rpm | 2200 rpm | |
| Fan drive type | Hydraulic | |
| Lubrication system: | ||
| Method | Gear pump, force lubrication | |
| Filter | Full-flow | |
| *EPA Tier 4 Final emission certified |
Dual-path, hydrostatic transmission provides infinite speed changes up to 5.3 km/h / 8.5 mph. The variable capacity travel motors allow the operator to select the optimum speed to match specific jobs. Travel control lock lever and neutral switch.
| Travel speed (quick shift mode)* | Forward | Reverse |
| 1st | 0–2.1 mph 0–3.4 km/h | 0–2.5 mph 0–4.1 km/h |
| 2nd | 0–3.5 mph 0–5.6 km/h | 0–4.0 mph 0–6.5 km/h |
| 3rd | 0–5.3 mph 0–8.5 km/h | 0–5.3 mph 0–8.5 km/h |
| Travel speed (variable mode) | Forward | Reverse |
| 0–5.3 mph 0–8.5 km/h | 0–5.3 mph 0–8.5 km/h | |
| *Quick shift speeds are adjustable in the monitor. |
| Suspension | Rigid type | |
| Track roller frame | Monocoque, large section, durable construction | |
| Rollers and idlers | Lubricated track rollers | |
| Sealed and lubricated track | Track tension is easily adjusted with grease gun. | |
| Number of track rollers (each side) | 6 | |
| Type of shoes (standard) | Single grouser | |
| Number of shoes (each side) | 39 | |
| Grouser height | 1.9" | 47 mm |
| Shoe width (standard) | 20" | 510 mm |
| Ground contact area | 3,707 in² | 23919 cm² |
| Ground pressure (with dozer, ROPS cab) | 5.8 psi | 0.41 kgf/cm² / 40.3 kPa |
| Track gauge | 5'4" | 1620 mm |
| Length of track on ground | 7'8" | 2345 mm |
| Coolant | 9.0 U.S. gal | 34 ltr |
| Fuel tank | 50.2 U.S. gal | 190 ltr |
| Engine oil | 2.9 U.S. gal | 11 ltr |
| Hydraulic tank | 15.8 U.S. gal | 60 ltr |
| Final drive (each side) | 0.9 U.S. gal | 3.5 ltr |
| Diesel Exhaust Fluid (DEF) | 4.1 U.S. gal | 15.4 ltr |
| Tractor weight: | Including ROPS cab, U frame for power angle tilt dozer, rated capacity of lubricant, coolant, full fuel tank, operator, and standard equipment. | |
| 18,342 lb | 8320 kg | |
| Operating weight: | Including Power Angle Tilt dozer, ROPS cab, operator, standard equipment, rated capacity of lubricant, hydraulic control unit, coolant, and full fuel tank. | |
| 21,848 lb | 9910 kg | |
| Closed-center Load Sensing System (CLSS) designed for precise and responsive control, and for efficient simultaneous operation. | ||
| Hydraulic control unit: | ||
| All spool control valves externally mounted remote to the hydraulic tank. Piston-type hydraulic pump with capacity (discharge flow) of 99 ltr/min 26 U.S. gal/min at rated engine rpm. | ||
| Relief valve setting | 3,974 psi | 27.4 MPa / 280 kg/cm² |
| Hydraulic cylinders | Double-acting, piston type | |
| Number of cylinders: | Bore | Bore |
| Blade lift / 2 | 3" | 75 mm |
| Blade tilt / 1 | 3.6" | 90 mm |
| Blade angle / 2 | 3.1" | 80 mm |
| Blade pitch | 1 adjustable linkage | |
| Hydraulic oil capacity (refill): | ||
| Power angle tilt dozer | 17 U.S. gal | 64 ltr |
| Control valves: | ||
| 3-spool control valve for Power Angle Tilt dozer | ||
| Positions: | ||
| Blade lift | Raise, hold, lower, and float | |
| Blade tilt | Right, hold, and left | |
| Blade angle | Right, hold, and left | |
| Additional control valve required for ripper | ||
| Positions: | ||
| Ripper lift | Raise, hold and lower |
KOMATSU
Name : KOMATSU
Service Tel : (8621)-6841-4567
E-mail :
Web Site : https://home.komatsu/en/
Address :
Copyright Notice 2002-2024 global-ce.com Construction Machinery Online. All rights reserved.
Address: Room 901, Building C, Ruipu Mansion, Hongjunying South Road No.15, Chaoyang District, Beijing.100107 P.R.China
